12/250 (12X346)

Fonctionnement / Montage - Le goujon FBN II GS convient pour le montage en attente et le montage traversant dans certaines conditions, il convient également pour le montage à distance. - Avant le montage, placer l'écrou hexagonal dans la position optimale (l'extrémité du goujon doit dépasser d'environ 3 mm de l'écrou). - Lors du serrage, le goujon est tiré dans la bague d'expansion et l'expanse contre les parois du trou de forage. - Le marquage de tête permet un contrôle aisé de l'ancrage. - Pour l'installation en série, nous recommandons l'utilisation de l'outil de pose pour goujons d'ancrage FABS (article n° 077937.)

Description complète

Numéro d'article	45586FIS
Diamètre
Longueur
Principales caractéristiques	Functioning - The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions. - Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut). - When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall. - The head embossing offers a simple control of the anchoring. - In the case of series installation, we recommend using the FABS bolt anchor setting tool.
ETA-approval	Yes
Info	d_o= Nominal diameter of drill bit. t_fix= Grip range. h_ef= Effective anchorage depth. Min. t_d= Recommended drilling depth. kN = Load in kN. The allowable load is valid for one single anchor, at cracked concrete (tensile zone) with concrete class C20/25, incl. partial safety factor γ_f= 1,4 and if the S_cr, N and C_cr, N are taken in to account. When reduction on spacing and edge distance take place a re-calculation of forces should be carried out by making use of the technical guide or calculation software, they are available on request. Final calculations should comply with the complete European Technical Approval (ETA), this approval is also available on request.

Voir toutes les spécifications

Emballé par 10

Boîte complete uniquement

Spécifications & normes
Téléchargements

Spécifications

Diamètre	M12
Longueur	100 mm
Principales caractéristiques	Functioning - The FBN II is suitable for pre-positioned and push-through installation; also suitable for stand-off installation under certain conditions. - Prior to installation, place the hexagon nut in the optimal position (the drive-in pin projects by approx. 3 mm out of the hexagon nut). - When applying the torque, the cone bolt is pulled into the expansion clip and expands it against the drill hole wall. - The head embossing offers a simple control of the anchoring. - In the case of series installation, we recommend using the FABS bolt anchor setting tool.
ETA-approval	Yes
Info	d_o= Nominal diameter of drill bit. t_fix= Grip range. h_ef= Effective anchorage depth. Min. t_d= Recommended drilling depth. kN = Load in kN. The allowable load is valid for one single anchor, at cracked concrete (tensile zone) with concrete class C20/25, incl. partial safety factor γ_f= 1,4 and if the S_cr, N and C_cr, N are taken in to account. When reduction on spacing and edge distance take place a re-calculation of forces should be carried out by making use of the technical guide or calculation software, they are available on request. Final calculations should comply with the complete European Technical Approval (ETA), this approval is also available on request.

Télécharger en PDF Imprimer

La description

Numéros d'articles

Numéro d'article	45586FIS
EAN	4006209455869
UBB	500616649546
UNSPSC	31162101
N° Article du fabricant	45586

Télécharger des informations supplémentaires