Fabory | Masters in Fasteners
HV vs HR Assemblies: What's the Difference?
HV and HR are two distinct high-strength structural bolting systems covered by EN 14399. Both are designed for preloaded steel connections, but they differ in their component geometry, how they accommodate deformation and their response to overtightening.
Understanding these differences helps engineers, steel fabricators and procurement teams specify compatible assemblies, control installation and meet project requirements.
Structural bolting explained
What are HV and HR structural bolting assemblies?
HV and HR assemblies are high-strength structural bolting systems intended for use in preloaded steel connections. They consist of compatible bolts, nuts and washers that are selected and installed as a defined assembly.
The designation is not simply a description of bolt strength. HV and HR represent different systems within the EN 14399 series, each with its own geometry and approach to achieving the required ductility of the bolting assembly.
01
Preloaded connections
Both systems are designed for structural connections requiring a specified bolt preload.
02
Complete assemblies
Bolts, nuts and washers must be compatible with the specified system and supplied accordingly.
03
Controlled installation
Correct tightening, inspection and documentation are essential to achieving the specified connection performance.
Important: HV and HR assemblies are not automatically interchangeable. Selecting the correct system starts with the structural design and project specification, not visual similarity or stock availability.
Technical comparison
HV vs HR: the key differences
The principal technical difference is how the two systems are designed to accommodate plastic deformation. This affects their nut geometry, bolt thread length and behaviour when tightening loads exceed the intended level.
Why does the ductility mechanism matter?
During tightening, a preloaded structural bolting assembly must achieve the required preload while providing a suitable margin against overtightening and failure.
In an HR assembly, the bolt is designed to provide most of the plastic elongation. In an HV assembly, deformation is predominantly accommodated by the engaged threads. These differences influence the behaviour of the complete assembly, which is why bolts and nuts from the two systems must not be mixed.
Standards and compliance
How does EN 14399 apply to HV and HR assemblies?
EN 14399 is the European series covering high-strength structural bolting assemblies for preloading. Different parts of the series address general requirements, preloading suitability and specific assembly systems.
EN 14399-1
General requirements for high-strength structural bolting assemblies intended for preloading.
EN 14399-2
Suitability testing to establish the behaviour of bolting assemblies during preloading.
EN 14399-3
Requirements for system HR hexagon bolt and nut assemblies.
EN 14399-4
Requirements for system HV hexagon bolt and nut assemblies.
EN 15048 is different: EN 15048 covers structural bolting assemblies for non-preloaded connections. It must not be confused with EN 14399 assemblies specified for preloading.
Selecting the correct system
When should HV or HR assemblies be used?
The correct choice comes from the structural design, project specification, applicable standards and intended installation method. HV and HR should not be treated as interchangeable alternatives based on price or availability.
Specify HV when:
- The structural design explicitly identifies the HV system.
- The connection requires a suitable preloaded assembly.
- Installation procedures are appropriate for the specified HV assembly.
- Compatible components and documentation can be supplied.
Specify HR when:
- The structural design explicitly identifies the HR system.
- The connection requires a suitable preloaded assembly.
- Installation procedures are appropriate for the specified HR assembly.
- Compatible components and documentation can be supplied.
Both systems are used in European steel construction. Regional practice can differ, with HR widely associated with British and French practice and HV with German practice. Project requirements take precedence over regional convention.
Installation and quality
Why installation control matters
The performance of a preloaded connection depends on more than bolt strength. Correct assembly selection, tightening procedures, surface conditions and inspection practices all influence whether the specified preload can be achieved reliably.
01
Component compatibility
Use bolts, nuts and washers intended for the selected system. Do not substitute components without appropriate technical approval.
02
Tightening method
Follow the specified method and applicable requirements of EN 1090-2 and the assembly manufacturer's instructions.
03
Coating and lubrication
Verify the specified finish, lubrication condition and any relevant tightening characteristics of the assembly.
04
Inspection and records
Maintain the installation records, product identification and documentation required by the project quality plan.
Do not apply a generic tightening torque. The required procedure depends on the assembly, specified preload, tightening characteristics and installation method. Use the approved project procedure and applicable technical instructions.
Before placing an order
HV and HR assembly selection checklist
Before purchasing structural bolting assemblies, confirm that the complete product specification, installation requirements and documentation expectations are clear.
1. Confirm the specified system
Is the required assembly HV (EN 14399-4) or HR (EN 14399-3)? Do not substitute one system for another without design approval.
2. Verify dimensions and strength class
Confirm diameter, length, property class, thread arrangement and other specified characteristics.
3. Confirm the complete assembly
Verify the appropriate bolt, nut and washer combination, including compatibility and any assembly identification requirements.
4. Check surface treatment and tightening requirements
Confirm coating, lubrication, installation method and any specified tightening characteristics or suitability information.
5. Confirm documentation and traceability
Identify the Declaration of Performance, conformity information, inspection certificates and traceability records required for the project.
6. Agree delivery and project requirements
Confirm quantity, availability, packaging, project schedule and any other conditions relevant to receiving and using the assemblies.
Procurement tip: Specify the full assembly and its supporting documentation at the enquiry stage. Ordering by nominal bolt diameter and property class alone is not sufficient for a preloaded structural bolting connection.
Avoid unnecessary risk
Common mistakes when specifying HV and HR assemblies
Many structural bolting problems begin before installation. Clear specifications and careful procurement can help prevent incorrect assemblies reaching the construction site.
Assuming HV and HR are interchangeable
Similar dimensions or strength classes do not make the two systems equivalent.
Mixing assembly components
Combining incompatible bolts, nuts or washers may compromise the intended assembly behaviour and conformity.
Overlooking tightening controls
Preloaded connections require the appropriate tightening procedure and inspection arrangements.
Requesting documentation too late
Certificates, declarations and traceability requirements should be identified before ordering.
Fabory expertise
How Fabory supports structural bolting projects
Fabory supports steel construction customers with structural bolting products, technical enquiries, documentation requirements and project-focused supply. Our specialists can help procurement and engineering teams identify suitable product routes in line with the specified assembly system.
Structural bolting selection
Support with identifying the appropriate product specifications and structural bolting system.
Product availability
Access to structural bolting products and support with project requirements and supply planning.
Documentation support
Assistance with product documentation enquiries and requirements for quality assurance and project handover.
Product availability, supported systems and documentation vary by market and product specification.
Continue learning
Related steel construction guides
Explore related guidance on structural fastener selection, standards, documentation and fastening solutions for steel construction.
STRUCTURAL FASTENERS
EN 15048 vs EN 14399
Understand the differences between non-preloaded and preloaded structural bolting assemblies.
Read the selection guideCOMPLIANCE
Certificates and Documentation
Learn about inspection certificates, declarations, technical information and project traceability.
Explore documentationINDUSTRY SOLUTIONS
Steel Construction Expertise
Discover Fabory's range of structural fasteners, anchoring products and project support.
Explore steel constructionTechnical questions answered
Frequently asked questions about HV and HR assemblies
What is the difference between HV and HR assemblies?
Both are high-strength structural bolting systems for preloaded connections. HV assemblies, covered by EN 14399-4, achieve ductility predominantly through deformation of engaged threads. HR assemblies, covered by EN 14399-3, achieve ductility predominantly through plastic elongation of the bolt.
Are HV and HR bolts interchangeable?
No. HV and HR are distinct assembly systems with different design characteristics. They should not be substituted or combined without appropriate engineering assessment and approval.
Which standard applies to HV and HR assemblies?
HV hexagon bolt and nut assemblies are covered by EN 14399-4 and HR hexagon bolt and nut assemblies by EN 14399-3. Both form part of the EN 14399 series for high-strength structural bolting assemblies for preloading.
Why are HV assemblies more sensitive to overtightening?
HV assemblies are designed to accommodate deformation predominantly through the engaged threads. This makes their behaviour under excessive tightening different from HR assemblies and generally requires particular attention to tightening control and inspection procedures.
What is the difference between EN 14399 and EN 15048?
EN 14399 covers high-strength structural bolting assemblies intended for preloading. EN 15048 covers structural bolting assemblies used without specified controlled preloading. Selection must follow the connection design and project requirements.
Can I mix bolts, nuts or washers from HV and HR systems?
No. Components should be selected as a compatible assembly according to the specified system and relevant standards. Mixing components may affect tightening behaviour, conformity and the intended performance of the connection.
What should I confirm before ordering HV or HR assemblies?
Confirm the specified system, standard, dimensions, strength class, complete bolt-nut-washer combination, coating, tightening requirements and any documentation or traceability requirements. These should be established before placing the order.
Fabory | Masters in Fasteners
Need help selecting HV or HR structural bolting assemblies?
Fabory supports steel construction professionals with structural bolting selection, product supply and documentation enquiries. Share your project specification so our specialists can help identify the appropriate next steps.
Creating peace of mind.