text.skipToContent text.skipToNavigation

Kotvící šroub M10X95/10

Objednací číslo 96907FIS
Průměr
Klíčové vlastnosti Functioning - The FHB II-A L is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation. - When using FHB II-A L in push-through installation, the annular gap is to be filled with the injection mortar FIS HB. - The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole. - When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. - The styrene-free vinyl ester mortar fully seals the drill hole. - When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art.-No. 62420.
ETA-Certifikát Yes
Info
  • do= Nominal diameter of drill bit.
  • Min. td= Recommended drilling depth.
  • hef= Effective anchorage depth.
  • tfix= Grip range.
  • s = Width across flats.
  • kN = Load in kN.
  • The allowable load is valid for one single anchor, at cracked concrete (tensile zone) with concrete class C20/25, incl. partial safety factor γf= 1,4 and if the Scr, N and Ccr, N are taken in to account.
  • Final calculations should comply with the complete European Technical Approval (ETA), this approval is also available on request.

Specifikace

Průměr M10
Klíčové vlastnosti Functioning - The FHB II-A L is a bonded anchor with torque-controlled expansion for pre-positioned and push-through installation. - When using FHB II-A L in push-through installation, the annular gap is to be filled with the injection mortar FIS HB. - The anchor rod can be set either with injection mortar FIS HB or with the capsule FHB II-P / FHB II-PF HIGH SPEED, and is fully bonded in the drill hole. - When tightening the hexagon nut, the anchor rod cones are pulled into the mortar shell, which expands against the drill hole wall. - The styrene-free vinyl ester mortar fully seals the drill hole. - When using the resin capsule, set the anchor rod through rotating and hitting motions with a hammer drill. Use the RA-SDS setting tool, Art.-No. 62420.
ETA-Certifikát Yes
Info
  • do= Nominal diameter of drill bit.
  • Min. td= Recommended drilling depth.
  • hef= Effective anchorage depth.
  • tfix= Grip range.
  • s = Width across flats.
  • kN = Load in kN.
  • The allowable load is valid for one single anchor, at cracked concrete (tensile zone) with concrete class C20/25, incl. partial safety factor γf= 1,4 and if the Scr, N and Ccr, N are taken in to account.
  • Final calculations should comply with the complete European Technical Approval (ETA), this approval is also available on request.

Popis

Princip funkce - FHB II-A L je lepená rozpěrná kotva s řízením síly pro průvlečnou nebo předsazenou montáž. - U kotvy FHB II-A L se kruhová štěrbina při průvlečné montáži vyplní injektážní maltou FIS HB. - Kotevní svorník může být použit podle volby s injektážní maltou FIS HB nebo patronou FHB II-P(F), která se po celé ploše přilepí do vyvrtaného otvoru. - Při utahování šestihranné matice se kužely kotevního svorníku vtáhnou do maltového pouzdra, které se rozepne proti stěně vrtaného otvoru. - Bezstyrenová vinylesterová malta úplně utěsní vyvrtaný otvor. - Při použití patrony s maltou aplikujte kotevní svorník pomocí vrtacího kladiva s rotačním příklepem. K tomu použijte osazovací nástroj RA-SDS, objednací číslo 62420.

Čísla materiálu

Objednací číslo 96907FIS
EAN 4006209969076
UBB 500616706395
UNSPSC 31162101
Výrobní číslo položky 96907
Tuto stránku nezavírejte. Tato zpráva zmizí, jakmile se stránka zcela načte.